CORD STOCK

  • O-RING CROSS SECTIONS from 0.039" (1.0MM) through 2" (50.0MM) are stock in 70 Buna.
  • FLUOROCARBON, Silicone, EPDM and Neoprene are inventoried in 0.063" to 1" diameters.
  • HARD TO FIND COMPOUNDS AND DUROS such as Buna 90, 70 White FDA Buna & EP, Fluorosilicone, Aflas, Polyurethane and Polyisoprene are stocked in various cross sections.
  • 4 Lobed Profile (Q) profiles from 0.070" to 0.500" are inventoried in Buna N and Fluorocarbon.
  • 50 AND 60 DUROS stocked in many cross sections and compounds.
  • SQUARE cross-sections from 0.099" to 1.000" stock in Buna, EPDM, Silicone, and Fluorocarbon.
  • SPONGE profiles and cord stock from Neoprene, EPDM and Silicone.
  • CUSTOM RUBBER EXTRUSIONS

  • Extruded tubing available from most elastomers.
  • Profiles and shapes extruded from most elastomers.
  • Tight tolerance centerless ground material available in all durometers 50 and above to 0.750".
  • Cut lengths, plugs and washers available from all compounds.
  • Profiles spliced to various shapes such as window gaskets.
  • SPLICED AND VULCANIZED RINGS

  • Heat spliced and/or cold bonded rings available from all durometers & cross sections listed.
  • SPLICING KITS

  • O-Ring splice kits, which contain cord stock, splicing fixtures and adhesive are available in Buna N, Neoprene, EPDM, Fluorocarbon and Silicone. Buna kits available in square, 4 Lobed Profile (Q) and metric sizes.
  • O-RINGS

  • NO TOOLING CHARGE AND LOW MINIMUMS ON MOST CUSTOM SIZES!
  • AS-568 O-rings in stock in your choice of compounds and durometers.
  • Metric sizes available in various compounds and durometers.
  • SQUARE CUT RINGS

  • 70 Duro Buna N Square Rings are stocked in those sizes that fit AS568A O-Ring grooves.
    006S - 050S
    106S - 178S
    203S - 273S
    325S - 375S
    425S - 449S
  • Many sizes in stock in 75 Duro Fluorocarbon.
  • LATHE CUT RINGS

  • Custom Lathe cut rings up to 31.000" OD - MOST WITHOUT TOOLING from the following: Nitrile ( Buna ), Chloroprene ( Neoprene), EP, EPDM, EPT, Fluoroelastomer (Viton®, Fluorel, Aflas) Silicone, Polyacrylate, SBR, Epichlorohydrin (Hydrin), Vamac, Polyisoprene (Isoprene) Butyl, Bromobutyl & Chlorobutyl, Hypalon®, Chlorinated Polyethylene, TPR (Santoprene)
  • Compounds to satisfy FDA requirements.
  • Compounds compatible with Polycarbonates and other plastics.
  • Durometers from shore "A" 40 to 90.
  • Thickness from 0.020 +/- .005".
  • Square Ring Kits.
  • 4 Lobed Profile (Q) RINGS

  • 4 Lobed Profile (Q) rings available in Buna N & Fluoroelastomer.
  • Sizes not tooled can be heat spliced, for which there is no tooling.
  • Allied Seals Inc.
    PO Box 4913
    7345 N. Ridgeway Ave.
    Skokie, IL 60076
    Phone: (847)673-2080 Fax: (847)673-0034



    Hypalon® and Viton® are registered trademarks of DuPont Performance Elastomers.
    hosted by NetSource